How can I find the error line in a multi file document? Usually WinEdt5 goes to the error line when double clicking on an error (at least with single files). When I include files, this is not working anymore and it jumps to the last line of the main file. I also don't know where to look up the error line by hand as it gives me e.g. an error on line 906, which is somewhere in the included files but I have no idea where. Is the an output file where I can look up the line numbers and find the error? (I'm using PDFLatex). Jumping to the error line would of course be even better.
[Tex/LaTex] How to find the error line in a multi file document
errorswinedt
Related Solutions
Double clicking on the error...
It sounds like you're using some front-end application to compile. I can think of two possible ways to do some more error seeking:
1) Try only compiling the problem file. This may require temporary alteration of the preamble to make everything else work, but should still work after that.
2) What I would recommend: take it to the command line if you can. Trying running pdflatex (or just plain ol' latex) on the whole project and go through the output to see where it errors out. (This should also be possible with whatever front-end compiler you're using; scrolling through the compilation log is all-telling.)
What's the most effective way to find the name of the file in which under- or over- full warnings occur?
Search the .log file for the string erfull (either in text editor or command-line tool). This will give you all the overfull and underfull box warnings. The warnings will tell you which lines in the source file the error came from, and the log file will also indicate which PDF page the error occurred on.
As you read through the log file you can see each inputted subfile as it is opened. The warnings that occur after each filename pertain to the line numbers in that file.
I have concocted a example to demonstrate this, which I hope will not be too confusing. The file below is structured like so:
Main file includes
section.texsection.texinputstable1.texsection.texinputssubsection.texsubsection.texinputstable2.tex
Both of the table files create egregious box overflows.
The first erfull warning in the main .log file is this:
(./section.tex (./table1.tex)
Overfull \hbox (3524.03448pt too wide in paragraph at lines 12-11
Looking at the generated subfiles section.tex and table1.tex, we can see that the overfull tabular environment in table1.tex starts on line 12 of table1.tex. This is the source of the 12 at the beginning of the page range in the warning.
table1 is input into section.tex, on line 11 of section.tex. This is the source of the 11 in the warning page range.
So the log message may be translated as follows:
I opened the file
section.tex. Then I input the filetable1.tex. When I input the file, I found an overfull\hboxsomewhere between line 12 oftable1.texand line 11 ofsection.tex.
So to answer your question, how to find the name of the file in which the under- or overfull box occurs, it is in the file most recently referenced in the log file before the warning.
Here is the example:
\documentclass{article}
\usepackage[nopar]{lipsum}
\usepackage{filecontents}
%***************************************
\begin{filecontents}{table1.tex}
\begin{tabular}{llll}
a & b & c & \lipsum[1]\\
\end{tabular}
\end{filecontents}
%***************************************
\begin{filecontents}{table2.tex}
\begin{minipage}{1in}
\lipsum[1]
\end{minipage}
\end{filecontents}
%***************************************
\begin{filecontents}{subsection}
\subsection{Minipage}
\input{table2}
\end{filecontents}
%***************************************
\begin{filecontents}{section.tex}
\section{Confusion}
a
b
\input{table1}
d
e
f
\clearpage
\input{subsection}
\end{filecontents}
%***************************************
\begin{document}
\tableofcontents
\include{section}
\end{document}
Best Answer
[To get this off the unanswered list]
You are using a really obsolete version of WinEdt...
Every version >=6 is able to locate the error in the right file.
It suffices that you set your main document as a "main file" through the command "Set Main File" available in the "Project" menu or in the Tree interface toolbar.