Just a guess: The air get warmer inside the cracks and this (warmer plus moving lower pressure air) evaporates the water on the surface near the cracks. The reason why the air gets hotter inside the cracks is that the concrete is still warmer than the outside air, and the cracks have a larger surface to volume ratio.
Paper, especially when freshly cut, might appear to have smooth edges, but in reality, its edges are serrated (i.e. having a jagged edge), making it more like a saw than a smooth blade. This enables the paper to tear through the skin fairly easily. The jagged edges greatly reduce contact area, and causes the pressure applied to be rather high. Thus, the skin can be easily punctured, and as the paper moves in a transverse direction, the jagged edge will tear the skin open.
Paper may bend easily, but it's very resistant to lateral compression (along its surface). Try squeezing a few sheets of paper in a direction parallel to its surface (preferably by placing them flat on a table and attempting to "compress" it laterally), and you will see what I mean. This is analogous to cutting skin with a metal saw versus a rubber one. The paper is more like a metal one in this case. Paper is rather stiff in short lengths, such as a single piece of paper jutting out from a stack (which is what causes cuts a lot of the time). Most of the time, holding a single large piece of paper and pressing it against your skin won't do much more than bend the paper, but holding it such that only a small length is exposed will make it much harder to bend. The normal force from your skin and the downward force form what is known as a torque couple. There is a certain threshold torque before the paper gives way and bends instead. A shorter length of paper will have a shorter lever arm, which greatly increases the tolerance of the misalignment of the two forces. Holding the paper at a longer length away decreases this threshold (i.e. you have to press down much more precisely over the contact point for the paper to not bend). This is also an important factor in determining whether the paper presses into your skin or simply bends.
Paper is made of cellulose short fibers/pulp, which are attached to each other through hydrogen bonding and possibly a finishing layer. When paper is bent or folded, fibers at the folding line separate and detach, making the paper much weaker. Even if we unfold the folded paper, those detached fibers do not re-attach to each other as before, so the folding line remains as a mechanically weak region and decreasing its stiffness. This is why freshly made, unfolded paper is also more likely to cause cuts.
Lastly, whether a piece of paper cuts skin easily, of course depends on its stiffness. This is why office paper is much more likely to cut you than toilet paper. The paper's density (mass per unit area), also known as grammage, has a direct influence on its stiffness.
Best Answer
When you look at a surface like sand, bricks, etc, the light you are seeing is reflected by diffuse reflection.
With a flat surface like a mirror, light falling on the surface is reflected back at the same angle it hit the surface (specular reflection) and you see a mirror image of the light falling on the surface. However a material like sand is basically lots of small grains of glass, and light is reflected at all the surfaces of the grains. The result is that the light falling on the sand gets reflected back in effectively random directions and the reflected light just looks white.
The reflection comes from the refractive index mismatch at the boundary between between air $\left(n = 1.004\right)$ and sand $\left(n \approx 1.54\right)$. Light is reflected from any refractive index change. So suppose you filled the spaces between the sand grains with a liquid of refractive index $1.54$. If you did this there would no longer be a refractive index change when light crossed the boundary between the liquid and the sand, so no light would be reflected. The result would be that the sand/liquid would be transparent.
And this is the reason behind the darkening you see when you add water to sand. The refractive index of water $\left(n = 1.33\right)$ is less than sand, so you still get some reflection. However the reflection from a water/sand boundary is a lot less than from an air/sand boundary because the refractive index change is less. The reason that sand gets darker when you add water to it is simply that there is a lot less light reflected.
The same applies to brick, cloth, etc. If you look at a lot of material close up you find they're actually transparent. For example cloth is made from cotton or man made fibres, and if you look at a single fibre under a microscope you'll find you can see through it. The reason the materials are opaque is purely down to reflection at the air/material boundaries.